欢迎进入济南济柴环能燃气发电设备·现金牛牛官网!

行业资讯

合金尾气发电机组:导致连杆螺栓断裂的四种原因

返回 2024.03.21 来源:http://www.xifiao.com 0

柴油机的连杆螺栓是一次性使用的,是不能重复利用的,连杆螺栓重复使用将极易导致断裂,打坏发动机汽缸体,导致发动机报废。是什么导致了柴油发电机组连杆螺栓断裂的呢?连杆螺栓断裂主要有四个方面:

The connecting rod bolts of diesel engines are disposable and cannot be reused. Reusing the connecting rod bolts can easily lead to breakage, damage to the engine cylinder block, and engine scrapping. What caused the connecting rod bolts of diesel generator sets to break? There are four main aspects of connecting rod bolt fracture:

装配时扭紧力矩过大,用力不均匀。由于装配中没有严格的配用扭力扳手,具体扭紧力矩又不太了解,认为越紧越好;紧固连杆螺栓用较长的加力杆,扭紧力矩过大,超过了螺栓材料的屈服极限,使连杆螺栓出现屈服变形,使之在冲击载荷的作用下因过度的伸长而断裂。应强调的是,一定要按标准扭紧连杆螺栓,千万不能认为越紧力量越大越好。

现金牛牛

Excessive tightening torque during assembly and uneven force application. Due to the lack of strict torque wrenches during assembly and a lack of understanding of the specific tightening torque, it is believed that the tighter the better; The use of a longer force rod to tighten the connecting rod bolts results in excessive tightening torque, exceeding the yield limit of the bolt material, causing the connecting rod bolts to undergo yield deformation and fracture due to excessive elongation under impact loads. It should be emphasized that the connecting rod bolts must be tightened according to the standard, and the greater the tightening force, the better.

柴油机的连杆分多种级别,在检修中应注意不能换用不同级别的连杆。如果在检修中由于马虎不仔细将连杆盖搞乱错装,会造成连杆大头结合面的配合不紧密,在发动机运行中会造成连杆盖松动而导致连杆螺栓的断裂。WD615系列柴油机连杆大头为斜切口型,斜切角呈45°,连杆盖和连杆大头结合面采用60°锯齿形定位结构,这种结构具有贴合紧密定位准确可靠结构紧凑的特点。如果在维修中将连杆盖搞乱错装,势必会造成结合面锯齿定位不好,极易造成发动机在工作中连杆盖的松动,而导致连杆螺栓的断裂。

The connecting rods of diesel engines are classified into multiple levels, and attention should be paid not to replace them with different levels during maintenance. If the connecting rod cap is mishandled and mistakenly installed due to carelessness during maintenance, it will cause the mating surface of the connecting rod big end to not fit tightly. During engine operation, it will cause the connecting rod cap to loosen and lead to the fracture of the connecting rod bolts. The connecting rod big end of WD615 series diesel engines is a slanted cut with a 45 ° angle. The joint surface between the connecting rod cap and the connecting rod big end adopts a 60 ° serrated positioning structure, which has the characteristics of tight fitting, accurate and reliable positioning, and compact structure. If the connecting rod cap is mixed up and installed incorrectly during maintenance, it will inevitably cause poor alignment of the serrations on the joint surface, which can easily cause the engine to loosen the connecting rod cap during operation and lead to the fracture of the connecting rod bolts.

柴油机在运行中出现飞车故障或活塞在气缸内烧死的故障,将连杆螺栓拉断。如果发动机在使用中出现过飞车的故障,应对发动机做一次全面检查,好更换连杆螺栓;如果在运行中个别气缸出现过较严重的拉缸,在更换气缸活塞组件时也应将连杆螺栓更换。

During operation, the diesel engine experiences a malfunction of speeding or the piston burns out in the cylinder, causing the connecting rod bolts to break. If the engine has experienced speeding faults during use, a comprehensive inspection of the engine should be conducted to replace the connecting rod bolts; If some cylinders have experienced severe cylinder pulling during operation, the connecting rod bolts should also be replaced when replacing the cylinder piston components.

材质问题加工缺陷及热处理工艺问题也会导致连杆螺栓在发动机运行中出现断裂。

Material issues, processing defects, and heat treatment process issues can also lead to the fracture of connecting rod bolts during engine operation.

·现金牛牛·新闻搜索
济南济柴环能燃气发电设备·现金牛牛
  • 服务热线

    0531-62325028
    0531-69951266

合金尾气发电机组:导致连杆螺栓断裂的四种原因

柴油机的连杆螺栓是一次性使用的,是不能重复利用的,连杆螺栓重复使用将极易导致断裂,打坏发动机汽缸体,导致发动机报废。是什么导致了柴油发电机组连杆螺栓断裂的呢?连杆螺栓断裂主要有四个方面:

The connecting rod bolts of diesel engines are disposable and cannot be reused. Reusing the connecting rod bolts can easily lead to breakage, damage to the engine cylinder block, and engine scrapping. What caused the connecting rod bolts of diesel generator sets to break? There are four main aspects of connecting rod bolt fracture:

装配时扭紧力矩过大,用力不均匀。由于装配中没有严格的配用扭力扳手,具体扭紧力矩又不太了解,认为越紧越好;紧固连杆螺栓用较长的加力杆,扭紧力矩过大,超过了螺栓材料的屈服极限,使连杆螺栓出现屈服变形,使之在冲击载荷的作用下因过度的伸长而断裂。应强调的是,一定要按标准扭紧连杆螺栓,千万不能认为越紧力量越大越好。

20230315052245106.jpg

Excessive tightening torque during assembly and uneven force application. Due to the lack of strict torque wrenches during assembly and a lack of understanding of the specific tightening torque, it is believed that the tighter the better; The use of a longer force rod to tighten the connecting rod bolts results in excessive tightening torque, exceeding the yield limit of the bolt material, causing the connecting rod bolts to undergo yield deformation and fracture due to excessive elongation under impact loads. It should be emphasized that the connecting rod bolts must be tightened according to the standard, and the greater the tightening force, the better.

柴油机的连杆分多种级别,在检修中应注意不能换用不同级别的连杆。如果在检修中由于马虎不仔细将连杆盖搞乱错装,会造成连杆大头结合面的配合不紧密,在发动机运行中会造成连杆盖松动而导致连杆螺栓的断裂。WD615系列柴油机连杆大头为斜切口型,斜切角呈45°,连杆盖和连杆大头结合面采用60°锯齿形定位结构,这种结构具有贴合紧密定位准确可靠结构紧凑的特点。如果在维修中将连杆盖搞乱错装,势必会造成结合面锯齿定位不好,极易造成发动机在工作中连杆盖的松动,而导致连杆螺栓的断裂。

The connecting rods of diesel engines are classified into multiple levels, and attention should be paid not to replace them with different levels during maintenance. If the connecting rod cap is mishandled and mistakenly installed due to carelessness during maintenance, it will cause the mating surface of the connecting rod big end to not fit tightly. During engine operation, it will cause the connecting rod cap to loosen and lead to the fracture of the connecting rod bolts. The connecting rod big end of WD615 series diesel engines is a slanted cut with a 45 ° angle. The joint surface between the connecting rod cap and the connecting rod big end adopts a 60 ° serrated positioning structure, which has the characteristics of tight fitting, accurate and reliable positioning, and compact structure. If the connecting rod cap is mixed up and installed incorrectly during maintenance, it will inevitably cause poor alignment of the serrations on the joint surface, which can easily cause the engine to loosen the connecting rod cap during operation and lead to the fracture of the connecting rod bolts.

柴油机在运行中出现飞车故障或活塞在气缸内烧死的故障,将连杆螺栓拉断。如果发动机在使用中出现过飞车的故障,应对发动机做一次全面检查,好更换连杆螺栓;如果在运行中个别气缸出现过较严重的拉缸,在更换气缸活塞组件时也应将连杆螺栓更换。

During operation, the diesel engine experiences a malfunction of speeding or the piston burns out in the cylinder, causing the connecting rod bolts to break. If the engine has experienced speeding faults during use, a comprehensive inspection of the engine should be conducted to replace the connecting rod bolts; If some cylinders have experienced severe cylinder pulling during operation, the connecting rod bolts should also be replaced when replacing the cylinder piston components.

材质问题加工缺陷及热处理工艺问题也会导致连杆螺栓在发动机运行中出现断裂。

Material issues, processing defects, and heat treatment process issues can also lead to the fracture of connecting rod bolts during engine operation.

2024-12-09